Nov 12, 2026 Leave a message

Overhead Conveyor Drive Sizing: Chain Pull, Torque and Power

Most drive problems on an overhead conveyor are decided before the quotation is written, in a chain pull figure that was estimated rather than summed. This article walks the arithmetic in the order an engineer should: resistances, safety factor, torque, power - and shows which assumptions change the answer most.

1. Chain pull comes before motor size

A drive is not chosen by looking at the load on the line. It is chosen by the force required to pull the chain around the whole circuit, including the empty half coming back. Two lines carrying the same parts can need drives a size apart, because one has six curves and a rising section and the other is a straight loop on one level.

That force is chain pull. Everything downstream - sprocket torque, reducer ratio, motor power, start-up behaviour - follows from it, which is why the calculation has to be done before a drive frame is drawn rather than after the first stall.

2. The resistances you are actually summing

Chain pull is a sum, and every term in it is a resistance that has to be overcome continuously. Miss one and the drive is undersized in a way that only appears under full load, at start-up, or after the chain has worn in.

The friction coefficient deserves attention because it is where most estimates quietly go wrong. It is not a single number for the product; it describes the wheel on the track, and it differs between a new sealed bearing, a bearing with dried grease, and a wheel that has flat-spotted at a curve entry. Values used in a calculation should be stated explicitly so that a reader can see whether they describe a new line or a worn one.

Resistance

What creates it

How it is handled

Loaded run friction

Trolley wheels rolling on the track under product and carrier weight

Coefficient times normal load; the single largest term on a level line

Return run friction

The empty chain and trolleys coming back

Same method with the empty mass - often forgotten, never zero

Curve and bend resistance

Side thrust at every horizontal and vertical curve

Added per curve; vertical curves also carry the lift term

Lift and descent

Raising product between levels

Mass times gravity times height; descent may recover some of it, but never assume it does

Drive and chain losses

Sprocket engagement, chain articulation, reducer efficiency

A percentage allowance on the sum, plus reducer efficiency when converting to motor power

3. A worked example

Take a level loop with 40 carriers on a 1.2 metre pitch, each carrying 80 kg of product on a 20 kg carrier, six 90-degree curves, and a chain speed of 6 metres per minute. The figures below are illustrative assumptions, not catalogue values, but the sequence is the one that matters.

Moving mass. 40 carriers at 100 kg is 4,000 kg, and because the chain is a closed loop the empty return half is part of the same circuit, so the mass is counted once across the whole path rather than twice.

Level friction. With a rolling coefficient of 0.02, the pull is 0.02 × 4,000 × 9.81, or roughly 785 N.

Curves. At an added 2.5 percent of the level pull per curve, six curves add about 118 N.

Losses. A 10 percent allowance for chain articulation and drive losses adds about 90 N, giving a running pull near 990 N.

Safety factor. Multiply by 1.5 for start-up, wear allowance and load imbalance, and the design pull is about 1,500 N.

That last number, not the 990 N running figure, is what the drive has to deliver - and it is the number most quotations leave out.

The example also shows which assumption moves the answer most. Doubling the coefficient to 0.04 takes the running pull from 990 to about 2,000 N and the design pull close to 3,000 N, which crosses into the next reducer frame and probably the next motor size. Doubling the curve allowance instead adds only around 120 N. If only one number is going to be verified, verify the friction coefficient.

4. The safety factor is not padding

A drive sized exactly at running pull works perfectly on the day of commissioning and fails in the second year, because four things move against it: chain and wheel wear raise friction, product weights drift upward, cold starts demand more torque than steady running, and a line that stops with parts on an incline has to restart against gravity rather than with it.

The factor is therefore a statement about how much unknown the design is carrying. A clean new line with known loads needs less of it than a retrofit where nobody can confirm what the original track was designed for.

Where it is applied matters as much as its value. The factor belongs on the pull, before torque and power are derived, so that it propagates into sprocket size, shaft, reducer and motor together. Applying it at the motor instead leaves the mechanicals sized for a pull the line will exceed in service - which is how a drive with a comfortable motor rating still breaks a chain.

5. From chain pull to torque and power

Torque at the drive sprocket is pull times radius. With a 0.3 metre pitch diameter, the radius is 0.15 m, so 1,500 N becomes about 225 N·m at the sprocket shaft.

Power is pull times chain speed. At 0.1 m per second the shaft power is about 150 W; dividing by a reducer efficiency of roughly 0.7 gives about 215 W at the motor, which lands on a standard 0.37 kW frame rather than a 0.25 kW one.

Note the order: torque sizes the reducer and the shaft, power sizes the motor, and both come from the same pull. Selecting a motor first and then finding a reducer to match it is how lines end up with a gearbox that cannot transmit the start-up torque the motor can produce.

6. What heat and length do to the number

A line through a cure oven has two extra terms that a level loop does not. The chain grows when hot, which the take-up absorbs, but a take-up near the end of its travel adds tension that shows up as friction; and trolleys running through a hot zone lose grease film faster, so the friction coefficient after a year is not the one measured at commissioning.

Long lines add a different problem: catenary sag between supports changes the effective path length and can add load at the drive if the chain is running tight over the sprocket. Neither effect is large on its own; together, on a 200 metre line in a hot zone, they are the reason a drive that was adequate on paper is marginal in service.

Vertical curves are the other place where the calculation and the installation diverge. A descending section recovers energy in theory, but only if the chain is fully supported and the descent is long enough to matter; in practice most short drops are treated as neutral, and the drive still has to lift on the other side of the circuit. Numbering the vertical curves separately from the horizontal ones keeps that asymmetry visible.

7. Five sizing mistakes that appear after installation

Counting only the loaded run. The return half is real mass and real friction, typically a third to a half of the loaded term on an empty line.

Using average product weight. A line that runs mixed parts is sized for the heaviest realistic pattern at the pitch that pattern occupies, not for the annual average.

Ignoring curve count. Adding two curves during layout revision is a pull increase, and nobody re-issues the drive calculation.

Sizing for steady running only. Start-up with a loaded, cold line is the governing case on most installations.

Forgetting the reducer. A motor with adequate power behind an undersized reducer fails at the gear, not at the winding.

Quoting a drive without the sprocket. Sprocket pitch diameter converts pull into torque; changing it after the reducer is chosen changes the required torque back again.

8. What to send for a drive quotation

Give the circuit length, the carrier pitch, the maximum product weight per carrier, the vertical rises and drops, the number and type of curves, the required chain speed, and whether the line starts loaded or empty. Add the ambient and oven temperatures if any part of the route is hot.

With those, chain pull, torque and motor size can be calculated and checked against the track and chain selected, instead of being inferred from the last similar project. That calculation is also how Hangzhou Ocean Industry Co., Ltd. sizes a drive before it quotes one.

Who supplies these lines

Hangzhou Ocean Industry Co., Ltd. has manufactured overhead conveyor systems, conveyor chain and paint line components in Hangzhou, China since 2005, with in-house forging, heat treatment and assembly. Chain, trolley wheels, drive units and take-up assemblies come from one engineering group, so a line arrives as a matched system rather than a collection of parts that have to be reconciled on site. OEM and custom work is built from your drawing.

Quality you can verify: ISO 9001 · ISO 14001 · ISO 45001 · CE · SGS Verified.

Contact info@auto-conveyor-lines.com or WhatsApp +86 135 8881 1830.

Send your layout, product weight and required output, and we will come back with a line concept plus the questions we still need answered.

FAQ

How is chain pull calculated for an overhead conveyor?

Sum the resistances around the whole circuit: loaded run friction, return run friction, curve resistance, lift, and drive losses. Multiply the total by a safety factor for start-up and wear, and that figure is the design pull.

What safety factor should a conveyor drive use?

There is no universal number. A new line with confirmed loads needs less than a retrofit with unknown track history. The factor should be stated in the calculation so it can be reviewed rather than buried in a motor choice.

Why does a drive need more torque at start-up?

Static friction is higher than running friction, product may be resting on an incline, and a cold chain is stiffer. The drive and reducer must transmit that peak, not just the steady-state figure.

Can I increase motor power instead of recalculating the drive?

Usually not. If the pull is higher than assumed, the chain, trolleys, track and reducer are all affected. A larger motor on the same mechanicals moves the failure from the motor to the gearbox or the chain.

Does chain speed change the required power?

Yes, directly: power is pull times speed. Doubling speed doubles shaft power at the same pull, which is why fast lines with heavy parts need disproportionately larger drives.

What happens if the drive is oversized?

Less than buyers expect. An oversized drive runs at low load, which is inefficient and can be harder to protect against overload, but it does not damage the line the way an undersized drive does.

How much spare capacity should be planned?

Plan for the safety factor, not for growth that has not been designed. If a second shift or heavier product is likely, size the track, chain and trolleys for it and state that in the calculation, rather than leaving the motor oversized as a substitute.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry