Bearing Gear Spreader
video

Bearing Gear Spreader

When the chain is running, the gear is used with the rack fixed at a specific position. The interaction between them generates and transfers a force, making the suspended workpiece rotate continuously. It is suitable for connection with a single pendant chain.
Send Inquiry
Product Introduction

Hangzhou Ocean Industry Co., Ltd. is one of the most experienced manufacturers and suppliers of bearing gear spreader in China. Welcome to wholesale customized bearing gear spreader at competitive price from our factory. Good service and quality products are available.

 

Product Description

Hangzhou Ocean Industry Co., Ltd. builds bearing gear spreaders at its own plant in Hangzhou, China, drawing on 20 years of overhead conveyor system engineering. A bearing gear spreader is a mechanical speed-control unit that lets one overhead conveyor chain run at several different speeds around a single circuit, without a second drive motor and without programming a variable-frequency drive. A pinion carried on a bearing-supported shaft meshes with a stationary rack bolted along a defined stretch of track; while a trolley passes that stretch the pinion rolls, and the ratio between the pinion pitch-circle diameter and the output sprocket fixes how fast the load-carrying dolly travels through the zone. Stretches that must run at the main chain speed carry no rack at all, and the pinion is retracted before the trolley reaches them. We supply standard units for enclosed-track and I-beam overhead conveyors, and build custom gear ratios, rack pitches and mounting geometries for OEM integration.

The unit exists because a process station and a transport leg want opposite things from the same chain. A spray booth, a curing oven, a plating tank or an adhesive-curing station needs a slow, repeatable pass at a speed set by the process recipe. The return leg and the load and unload area want the chain moving as fast as the drive allows, because time spent there produces nothing. Splitting the circuit into two or three separately driven loops is the usual answer, but every extra drive brings a motor, a gearbox, a controller, a chain take-up and an interface that has to stay synchronised with the rest of the line. The spreader takes that cost and those failure points out of the decision: one drive, one chain, and zone speeds produced by machined geometry instead of by electronics.

Each unit ships as a complete assembly - a geared shaft with integral pinion, two sealed rolling-element bearings, bearing housings with mounting ears, and the coupling interface that connects to the conveyor chain attachment point. Racks are supplied separately or as a matched pinion-and-rack set, depending on whether you are building a new zone or re-toothing track that is already in service. Because the ratio is set by the pinion and output diameters, changing a zone speed later means changing that rack segment rather than re-tuning a controller.

Bearing gear spreader assembly for overhead conveyor speed change

Where a Bearing Gear Spreader Fits in a Conveyor Layout

A line built around spreaders still has one drive, one chain and one closed circuit. What changes is that the circuit is mapped into zones on the drawing instead of being divided by transfer mechanisms. A zone is a length of track that carries a rack and a defined ratio, so the number of zones is simply the number of rack segments shown on the layout. Load and unload stations, transfer points and long straight return runs usually carry no rack, because nothing in those stretches benefits from a changed speed. Spray booths, ovens, process tanks, curing stations and inspection positions carry a rack because the process needs a controlled pass through them.

Two figures have to be settled for every zone before anything is ordered: the linear speed the process needs, and the length of track over which that speed has to be held. Speed comes from the ratio. Length comes from the rack. If the rack is shorter than the zone it governs, trolleys return to the main chain speed part way through the process and the dwell time becomes inconsistent from load to load. If it is longer than the zone, the rack runs into the next section of track and the layout has to be redrawn before the steel is cut.

Because a single rack carries whatever trolleys happen to be in mesh at the same moment, the structural load case to declare is not one trolley but the fully loaded condition - the greatest number of trolleys the zone can hold at once, each carrying its rated payload, plus the chain pull at that point in the circuit. That figure is what the rack mounting bolts, the bearing selection and the trolley interface are checked against, and it is the item most often missing when a layout arrives for quotation.

Engagement happens at the rack lead-in, and there is nothing for the operator or the control system to sequence. The pinion meets the first tooth of the rack, and from that point the trolley travels at the zone ratio until the rack ends, at which point the cam mechanism or the optional pneumatic actuator pulls the pinion clear and the trolley resumes the main chain speed. That is the whole cycle, repeated for every zone on the circuit.

Unit Build and Core Components

Bearing-Supported Rotating Assembly

The mechanism at the centre of the unit is a pinion gear on a shaft that turns freely relative to the trolley body, carried in two sealed rolling-element bearings. Which bearing goes in depends on the load case the track imposes. Where the rack engagement force is mainly radial, deep-groove ball bearings (6204-2RS or equivalent) are the standard choice. Where the chain pull has a significant axial component - inclined track sections, or layouts where the tension vector does not run parallel to the rail - paired tapered roller bearings (30204 or equivalent) carry the thrust. Both are grease-packed for life with a polyurea-thickened synthetic grease and closed with double-lip PTFE contact seals, which is what keeps airborne paint overspray, dust and wash-down moisture away from the rolling elements. The housings are machined from ductile iron (GJS-400-15 / ASTM A536 65-45-12) with press-fit bores held to ISO H7 so that bearing interference stays correct through the life of the unit.

Forged Alloy Steel Mounting Body

The body that ties the bearing housings to the conveyor trolley is hot-forged from AISI 4140 (42CrMo4) alloy steel, then normalised and tempered to a uniform fine-grain structure. Forging aligns the metal grain flow with the principal stress paths, which leaves the finished body with roughly 15 to 20 percent more fatigue endurance than the same geometry machined out of rolled plate - a difference that shows up as longer service between replacements on lines that stop and start frequently. Mounting faces are surface-ground flat to within 0.05 mm per 100 mm, so bolting the body to the trolley plate cannot pull the bearing bores out of alignment. Threaded mounting holes are tapped after heat treatment and fitted with stainless steel helical wire thread inserts (Heli-Coil or equivalent), which stops the threads galling or stripping when the unit is assembled and removed repeatedly in the field.

Engagement and Retraction Mechanism

A spring-loaded cam mechanism is the standard arrangement; a pneumatic actuator is available where zone changes have to be automated. In the engaged position a hardened steel locking pin seats in a detent on the cam profile, which is what stops vibration or chain pulsation from walking the pinion out of mesh part way through a zone. The retraction stroke is set so that the pinion clears the rack teeth by 2.0 to 2.5 mm when disengaged - wide enough that lateral sway of the trolley on the track cannot cause accidental tooth contact, and short enough that re-engagement needs less than 5 mm of actuator travel, which keeps the dead time between speed-change zones small.

Pinion and Rack Tooth Form

Pinion teeth are hobbed to AGMA Class 8 accuracy (DIN Class 8 equivalent) and then induction-hardened on the flank and the root. After hardening, the tooth flanks are finish-ground to remove the distortion the heat treatment introduces, returning the involute form to within 0.015 mm of theoretical. Racks use the same material and hardening specification, with tooth pitch held to within 0.025 mm accumulated over any 300 mm of length. Where the pinion and rack are supplied as a matched set, the pair is checked for backlash before dispatch, so the mesh does not have to be re-shimmed on site.

Material and Heat Treatment

Two failure modes drive the material specification: flank pitting from repeated rolling contact, and root-fillet cracking from shock loads when a chain snatch or an emergency stop sends a torque spike through the mesh. The specification answers both at once, because a tooth that is hard where it contacts and tough where it bends is the only way to keep a speed-control unit in service on a line that runs every day.

Item

Specification

Mounting body material

Hot-forged AISI 4140 / 42CrMo4, normalised and tempered

Body tensile strength

850 to 1000 MPa

Core hardness after tempering

HRC 28 to 32 (approx. 930 MPa tensile, 780 MPa yield)

Core impact energy

Charpy V-notch 40 J minimum at room temperature (ISO 683-2 minimum for structural steel is 27 J)

Gear tooth hardening

Medium-frequency induction, 8 to 12 kHz, polymer quench

Case hardness and depth

HRC 50 to 55, 1.5 to 2.0 mm at flank and root fillet

Surface residual stress

Approx. 300 to 400 MPa compressive after hardening

Post-hardening temper

180 to 200 °C for 2 hours

Tooth accuracy

Hobbed to AGMA Class 8 / DIN Class 8; flanks finish-ground to within 0.015 mm of theoretical involute

Rack tooth pitch tolerance

Plus or minus 0.025 mm accumulated over any 300 mm

Backlash, matched set

0.10 to 0.20 mm

Bearing housings

Ductile iron GJS-400-15 / ASTM A536 65-45-12, bores to ISO H7

Mounting face flatness

Ground to 0.05 mm per 100 mm

The reason the core is left tempered rather than hardened right through is a maintenance one. A case-hardened tooth riding on a tough core will, if it is ever overloaded, show measurable wear that a maintenance planner can schedule for. A tooth that is hard all the way through tends to fail as a fracture instead, and a fractured tooth on a live conveyor stops the whole line without warning. That trade is deliberate and it is the same reasoning behind the induction frequency and scan rate we use: the case-to-core transition is made gradual rather than abrupt, which avoids the subsurface tensile stress peak that causes case spalling on gears with a sharp boundary.

Corrosion Protection by Operating Environment

A spreader spends its working life in whatever atmosphere the plant has - oven heat, paint overspray, plating mist, wash-down water, coastal humidity. The coating system is chosen against that, not against a general-purpose standard.

Operating environment

Coating system

Salt-spray resistance (ASTM B117)

Indoor, dry workshop atmosphere

Zinc-nickel electroplate, 12 to 15 percent nickel, 8 to 12 µm, trivalent chromium passivate

720 hours minimum to red rust

Coastal site, chemical plant, offshore platform, tropical outdoor installation

Zinc-nickel plate plus zinc-rich epoxy primer and polyurethane topcoat

1500 hours minimum

Reference: conventional zinc plating with hexavalent chromate

Not supplied as standard

240 hours typical

Gear tooth flanks and bearing bores are masked during plating, so the coating never reaches a surface whose fit matters. That point is worth checking with any supplier, because a coated gear flank changes the effective tooth thickness and the backlash that was set on the bench is no longer the backlash in service. On plating and pickling lines, tell us which chemistries the unit will be exposed to as vapour rather than as splash - the atmosphere above a tank is usually the harsher environment, and it is the part of the decision most often overlooked when a coating is specified at quotation stage.

Speed Ratio and Zone Planning

The ratio is a property of two diameters, not a setting. The pinion diameter is fixed by the rack tooth pitch, and the output sprocket diameter is fixed when the unit is built, so the relationship between chain speed and dolly speed in a given zone can be written on the drawing before the unit exists.

Pinion pitch-circle diameter

Output sprocket diameter

Dolly speed relative to chain

80 mm

40 mm

0.5 x chain speed (2:1 reduction through the process zone)

50 mm

100 mm

2 x chain speed (return leg transit time halved)

Planning a zone therefore starts from the process, not from the conveyor. Work out the dwell time the process needs and the track length available for it, and the required speed follows. Divide that by the chain speed to get the reduction each zone needs, and the ratio table above is what the unit is then built to. A circuit that needs slow through curing, medium through inspection and fast through return is three ratios and therefore three rack segments, all driven by the one motor that was already on the line.

There is one consequence worth stating plainly, because it catches people out at the specification stage: the speed in a zone is fixed by machined geometry, so a later change of process recipe is a mechanical change, not a parameter change. Rack segments are bolted in place, so swapping one for a segment of a different pitch is a scheduled-maintenance job - but it is a job that has to be planned, ordered and shut down for. If the process recipe on your line changes often, that trade should be part of the conversation when the zone layout is agreed rather than after the racks have been delivered.

Rack Layout and Engagement Geometry

The rack is bolted to the track structure along the length of the zone it governs, with its teeth presented to the pinion. Its tooth pitch is what sets the zone ratio, so the pitch is fixed at the moment the zone speed is fixed. A rack segment cannot be exchanged for one of a different pitch without changing the speed of that zone - the two decisions are the same decision.

What the rack has to get right is where the pinion meets it. The pinion should enter along the tooth flanks rather than against a tooth face, which is a matter of lead-in geometry and of how the rack is aligned to the rail over its whole length. Accumulated pitch error is controlled to within 0.025 mm over any 300 mm of rack, because a pitch error that is small at the first tooth but compounds along the segment shows up as a progressive change in the ratio and therefore as a zone speed that is not the one the process was designed around. The mesh clearance in the retracted position is 2.0 to 2.5 mm, and re-engagement needs less than 5 mm of travel, so the transition at each end of a rack is short and does not need a length of special track reserved for it.

On the bench, a matched pinion and rack are checked for backlash between 0.10 mm and 0.20 mm before they are packed. That check is done with the pair as it will be installed, which is the reason a matched set is the safer choice for a new zone: the mesh does not depend on a shim pack that someone has to set correctly on a gantry at height. Where a spreader is being fitted to rack that is already on a track, the starting point is measuring that rack rather than replacing it - see the next section but one for what we need to match it.

Enclosed-Track and I-Beam Mounting Options

Standard configurations are available for both enclosed-track and I-beam overhead conveyor systems. The mechanism inside is the same in either case; what differs is how the unit hangs on the trolley and where the rack is anchored, and both of those follow from the track type rather than from the load.

On an enclosed-track line the rail is a closed profile, the trolley runs within it, and the spreader mounts to the trolley plate through the slot in the rail. The rack is anchored to the track support structure alongside the profile. On an I-beam line the trolley rides the flange, the mounting plate sits above the rail, and the rack typically follows the track structure rather than the rail itself. The housing mounting ears and the coupling interface are machined for the arrangement you specify, so the two are not interchangeable after the unit is built.

Two items settle this at enquiry stage: the track type, and the trolley mounting drawing or plate pattern you want the unit to bolt to. If the line mixes track types - enclosed track in the process area and I-beam on the return, which is common when an existing return line is reused - say so, because the rack anchoring detail changes between the two sections and the transition point has to be drawn rather than improvised on site.

Selection Inputs for Line Builders

A spreader is sized from the line, not from a catalogue page, so the enquiry needs to carry the line's operating figures. The list below is what we work from; anything missing is a question we will come back with before quoting, because guessing any of these items moves the cost into the second half of the project.

  • Circuit layout drawing showing where each zone starts and finishes, and the track length available for each rack
  • Required linear speed in each zone, or the dwell time and process length it is derived from
  • Main chain speed, and chain pull at the position where each spreader sits
  • Maximum trolley plus payload weight, and the greatest number of trolleys that will be in mesh on one rack at the same time
  • Trolley mounting plate pattern or drawing, including hole centres and plate thickness
  • Track type, enclosed profile or I-beam, with the rail or beam size
  • Ambient temperature at the unit, particularly where a zone runs through an oven
  • Operating environment, so the coating system can be confirmed
  • Duty cycle, hours per day and days per week, and whether the line stops and starts often
  • Actuator preference, spring-loaded cam or pneumatic, and whether the zone changes are to be automated
  • For a retrofit, the pitch, pressure angle and mounting pattern of the rack already installed

Bearing and Lubrication Service Life

The bearings are grease-packed for life with a polyurea-thickened synthetic grease and sealed with double-lip PTFE contact seals, so in normal service there is no grease point to visit. That is a deliberate design choice on overhead conveyors: a lubrication task at height, on a moving line, is a task that gets deferred, and a bearing that needs grease it does not receive fails long before a sealed bearing of the same size would.

What actually shortens bearing life on these units is the environment rather than the load. Paint overspray that builds up until it bridges the seal, wash-down chemicals that attack the seal lip, and misalignment that puts an edge load on the rolling elements are the three causes we see most often. All three are visible on inspection before they become a failure, which is why the maintenance section below concentrates on what to look at rather than on a greasing interval.

On the gear side, the calculation is more forgiving than the environment. At the tempered core hardness used here, the material's endurance limit sits around 420 to 480 MPa under fully reversed polished bending at fifty percent survival probability, and because the induction-hardened case is in compression, the effective fatigue limit at the critical root fillet is raised by roughly 25 to 30 percent over the core alone. For a typical overhead conveyor duty - 16 hours a day, six days a week, 50 weeks a year, a 30 m/min chain speed and the pinion in mesh for about 30 percent of the circuit - the calculated bending fatigue life at rated torque exceeds five years, provided the rack is aligned properly and the unit is not subjected to repeated overload. Service life in practice depends on lubrication condition here as much as anywhere, on alignment accuracy, and on how often the line produces a shock load.

Matching Racks, Trolleys and Chain Interfaces

Three interfaces decide whether the unit drops onto your line without modification: the rack to the track, the housing to the trolley plate, and the output to the chain attachment point. All three are machined to the drawings you send, so the enquiry drawing set matters more than the specification table.

The housing sits on the trolley mounting plate. Threaded mounting holes are tapped after heat treatment and fitted with stainless steel helical wire thread inserts, which is what allows the unit to be removed and refitted during maintenance without the threads giving up on the third or fourth cycle - a small detail that matters when the alternative is replacing a trolley body. Mounting faces are ground flat so that bolting down does not distort the bearing bores, and the plate itself has to be flat and free of weld spatter for that to hold.

The output side connects to a secondary sprocket or coupling that interfaces with the load-carrying dolly or with the secondary chain segment, depending on how the line carries product. Where an existing trolley is being reused, the useful information is its plate drawing, its current attachment arrangement and the load it carries. Where the spreader is being designed into a new line, we work from the general arrangement drawing and the chain attachment detail, which is where the ratio and the output diameter get fixed together.

Racks are supplied separately or as a matched pinion-and-rack set. The matched route is the one we recommend for a new zone and the one that removes any question about backlash. The separate route makes sense when you already hold rack stock at the right pitch, or when you are matching rack that is fixed to an existing track and cannot be removed for grinding.

Custom Ratios, OEM Mounting and Mixed-Product Lines

Custom gear ratios, rack pitches and mounting geometries are normal scope rather than a special project, because a ratio requirement is met by changing two diameters rather than by redesigning the unit. If a process needs a speed between the standard steps, the pinion pitch-circle diameter, the output sprocket diameter, or both are changed to produce it, and the housing envelope stays where it was. That keeps the unit inside the clearance you have already allowed in the layout.

The same property is what makes these units useful on mixed-product lines. Workpieces of different shapes and sizes can ride the same circuit at the same process speed, because the speed is set per zone rather than per product; changing a product only changes what rides the hook, not how the line is set up. A line can then run a large part and a small part through the same booth at the same pass speed without a second spreader or a second drive.

Units also drop into both automated and manually operated lines. On a manual line the spring-loaded cam mechanism is operated by the track itself and the operator has nothing to do; on an automated line the optional pneumatic actuator handles the same engagement on a signal, which is what allows zone changes to be coordinated with a PLC or with a recipe change. Whether the line is hand-loaded or fully automatic changes the actuator, not the mechanism.

Assembly, Alignment and Commissioning

Fitting the unit to a trolley is the short part of the job. Bolting the housing to the trolley mounting plate and aligning the pinion to the rack takes an experienced maintenance team around 30 minutes once the rack is in position and the trolley is off the line. The work that consumes the shutdown is establishing the rack position and proving the alignment over its full length.

The commissioning checks that matter are, in order: rack pitch measured over a 300 mm span against the drawing; rack alignment to the rail over the whole segment, not just at the ends; retracted clearance between pinion and rack teeth; re-engagement travel; backlash on a matched set; and a full circuit run with the trolley speed measured at each zone and compared with the ratio the layout called for. The last check is the one that catches drawing errors rather than manufacturing errors, and it is worth doing before product goes on the line, because a zone speed that is wrong shows up as a process defect long before it shows up as a mechanical one.

Two settings are easy to get wrong on site and expensive to discover late. The first is retracted clearance: set too tight, the pinion touches the rack on a track section that swayed during installation; set too loose it changes nothing, because the retraction stroke is bounded by the actuator travel available for re-engagement. The second is the locking pin detent, which has to be confirmed as seated in the engaged position before the line is handed over - on a manual unit this is what holds the pinion in mesh for the whole zone.

Inspection and Preventive Maintenance

Because the bearings are sealed for life and the mesh needs no adjustment in service, the maintenance routine for these units is an inspection rather than a service schedule. Five items cover the mechanism, and all five can be done from the floor or from a platform without stripping the unit.

Tooth flanks first. Look for polish and even contact across the flank, and for any sign that contact is concentrated at one end of the tooth or on one flank only - uneven contact is the earliest visible symptom of rack misalignment, and it appears long before the teeth are damaged. Second, backlash on a matched set, which should still be inside the 0.10 to 0.20 mm band; growth beyond that band points to wear or to the rack having moved. Third, the pinion should turn freely by hand with the unit off the line and show no detectable axial play or roughness; roughness means a bearing has taken on water or overspray and should be planned for replacement rather than left to fail. Fourth, the retracted clearance, checked with the pinion in the disengaged position. Fifth, the locking pin and cam detent, or on pneumatic units the actuator stroke, which should be confirmed as reaching full engagement and full retraction at each end of the zone.

Two further points are worth adding to whatever inspection regime the plant already runs. Check the rack mounting bolts after the first weeks of running, while the structure is still settling, and include them in routine walk-rounds afterwards - a rack that has shifted on its bolts is the origin of most of the faults in the next section. And keep overspray off the rack teeth. Coating that builds up in the tooth spaces changes the effective pitch, which changes the zone ratio by an amount that is small at first and progressive, and it is much easier to wipe off a rack during a shutdown than to re-cut one.

Faults That Trace Back to Rack Alignment

Most spreader problems that come back to us as a quality question turn out to be alignment problems, and they announce themselves in a predictable order. The first sign is noise at a zone boundary - a change in tone as the trolley enters or leaves the rack, which is the pinion meeting the lead-in at an angle instead of along the flank. The second is uneven flank contact, visible as a bright band on part of the tooth face and untouched metal on the rest. The third is backlash growth, as the uneven contact wears the loaded flank faster than the unloaded one.

The fourth sign is different in character and deserves separating: a trolley that does not return to the main chain speed at the end of a zone. That is a disengagement fault rather than a rack fault, and the things to check are the locking pin detent, the cam spring on manual units, and the actuator stroke on pneumatic ones. It is worth diagnosing rather than adjusting, because simply increasing actuator pressure to force disengagement will usually mask a detent problem until the pin and the cam profile are both worn.

Alignment corrections are a track job rather than a spreader job: re-set the rack to the rail over its full length, re-check the pitch over a 300 mm span, confirm the bolted fixings, then re-run the backlash and zone-speed checks. Where rack alignment cannot be corrected because the track structure itself has moved, the useful next step is a route survey of the zone rather than more adjustment of the spreader, because no amount of shimming at the unit will fix a rail that has drifted.

Applications: Paint and Powder Coating Lines

Automotive component painting is the application these units were developed around, because it puts three conflicting speed requirements on one chain within a few tens of metres of track. Bumpers, wheels, mirror housings and trim parts need the conveyor moving slowly and steadily through the spray booth, so that the coating goes on evenly and the operators or robots see a consistent pass. They then need a different speed through the curing oven, because the dwell time at temperature is what sets the cure, not the distance travelled. And in the cooldown and unloading area the only requirement is throughput, so the chain should run as fast as the drive allows.

Three rack segments - slow at the booth, a different ratio at the oven, fast at unload - deliver all three profiles from the single main drive that was already on the line. That removes the cost of two further drive units, and it removes the synchronisation problem that comes with them: separately driven conveyor sections sharing a track circuit have to stay in step through every stop, start and product changeover, and every one of those interfaces is a place where a jam can begin.

There is a secondary benefit in a paint shop specifically. Coating overspray that builds up on the spreader is unavoidable in that atmosphere, which is why the gear flanks and bearing bores are masked during plating and why the bearings are sealed rather than greasable - the two surfaces that must stay clean are the two that the design keeps closed.

Applications: Plating, Heat Treatment and Assembly Lines

Electroplating lines move parts through a sequence of chemical tanks - clean, rinse, etch, plate, rinse, passivate, dry - and each bath needs a different immersion time. Tank dimensions are fixed by the process, so the only variable available to the line designer is how fast the conveyor moves the part through each tank zone. A rack segment sized for each tank's dwell requirement is bolted along the corresponding stretch of track, and the pinion adjusts trolley speed as the part enters each zone. When a plating recipe changes, the change is a new rack segment installed during a scheduled shutdown; there is no PLC program to rewrite and no drive parameter to re-validate, which is worth having on a line where a wrong immersion time sends a batch to the scrap bin rather than to rework.

Continuous heat treatment and annealing furnaces put a different requirement on the same idea: dwell time in the soak zone has to be held precisely, and it has to stay held while the load and unload ends of the line run at whatever speed the throughput demands. A rack segment matched to the furnace length and the required soak time holds the trolley speed through the furnace independently of everything happening either side of it. The mechanical ratio is also the reason this works reliably in that position: the ambient temperature around a furnace is exactly where electronic speed sensors and drive feedback loops begin to drift or drop out, and a machined ratio does not care how hot the air is.

On appliance, furniture and electronics assembly lines the problem is cycle time rather than process chemistry - a 30-second screw-driving station, a three-minute adhesive curing station, a 90-second functional test and a 15-second packaging station, all on one overhead chain. Spreaders let the chain deliver a different speed at each station without breaking the line into separately driven segments joined by transfer mechanisms, which reduces the equipment count, the floor space the line occupies and the amount of system integration the project needs before it can run.

FAQ

Q: 1: What does a bearing gear spreader do that a variable-frequency drive cannot?

A: It changes the speed of one zone without a second drive unit. Because the ratio is set by the machined pinion and output diameters, the zone speed does not drift with electrical noise, power quality or controller parameters, and it holds through a power interruption. On continuous-process lines such as coating, heat treatment and plating that predictability matters more than the flexibility a drive offers, because a speed excursion can spoil hours of production before anyone notices.

Q: 2: How many different speeds can one circuit run with these units?

A: As many as you install rack segments for. Each segment carries a tooth pitch that corresponds to one ratio, so a circuit with a slow spray zone, a medium inspection zone and a fast return leg uses three segments and still runs from a single main drive. Any length of track without a rack runs at the main chain speed.

Q: 3: Which bearing arrangement should I specify for my installation?

A: Deep-groove ball bearings (6204-2RS or equivalent) are the standard choice where the engagement force is mainly radial, which covers most level, straight track sections. Paired tapered roller bearings (30204 or equivalent) are specified where axial thrust is present, such as inclined track or a layout where the chain tension vector does not run parallel to the rail. Send the track inclination and the expected chain pull and we will confirm the arrangement.

Q: 4: Is the pinion engaged all the way around the circuit?

A: No. It is in mesh only over the length of a rack segment. Between segments the cam mechanism, or the optional pneumatic actuator, retracts the pinion and the trolley continues at the main chain speed. In the retracted position the pinion clears the rack teeth by 2.0 to 2.5 mm.

Q: 5: What surface protection do you apply as standard, and when should I upgrade?

A: Standard is a zinc-nickel electroplate with a trivalent chromium passivate, rated to 720 hours of neutral salt spray before red rust appears (ASTM B117). For coastal sites, chemical plants, offshore platforms or humid outdoor installations we add a zinc-rich epoxy primer and a polyurethane topcoat, which extends the rating to 1500 hours. Gear tooth flanks and bearing bores are masked during plating so the coating never reaches a fitted surface.

Q: 6: Can you match a rack that is already installed on our track?

A: Yes, once the tooth geometry can be established. Send the pitch, the tooth count over a measured length, the pressure angle if it is known, and a photo or drawing of the tooth form together with the mounting hole pattern. We will quote a spreader that works with the rack rather than replacing it. A retrofit of this kind is normally fitted during a scheduled shutdown.

Q: 7: Do we buy the rack with the spreader, or separately?

A: Either way. A matched pinion-and-rack set is the safer route for a new zone, because the two parts are ground as a pair and checked for backlash before packing. If you already hold rack stock at the right pitch, or the rack is fixed to a track that cannot be removed, we supply the pinion alone and match it to the pitch you specify.

Q: 8: What is your delivery lead time?

A: Sample units are delivered in 30 working days. Production quantities ship in 60 working days from receipt of the deposit. On a retrofit where the existing rack geometry has to be established first, the lead time runs from the point that geometry is confirmed rather than from the enquiry.

Q: 9: What are your payment terms?

A: T/T with 30 percent as deposit and the 70 percent balance before delivery. We send photographs of the finished units and their packing before the balance is due, so you can confirm what is being shipped against what was ordered.

Q: 10: How often does the assembly need lubricating?

A: It does not, in normal service. The bearings are grease-packed for life with a polyurea-thickened synthetic grease and closed with double-lip PTFE contact seals, so there is no grease point to visit. The bearings are a replacement item at the end of their working life rather than a scheduled lubrication task, and the inspection points that predict that life are listed in the maintenance section above.

Q: 11: Can the unit be supplied for an I-beam conveyor instead of enclosed track?

A: Yes. Standard configurations are available for both enclosed-track and I-beam overhead systems. The mounting geometry and the coupling interface differ between the two and are machined for the arrangement you specify, so tell us which track type the line uses, and the trolley plate drawing, when you enquire.

Q: 12: What happens if the pinion does not fully disengage at the end of a rack?

A: The trolley stays partly coupled to the rack and the zone speed does not return to the main chain speed. In practice it appears as a change in tone at the zone boundary and as accelerated wear on one flank of the teeth. Check the locking pin detent first, then the cam spring on a manual unit or the actuator stroke on a pneumatic one. Forcing disengagement by raising actuator pressure tends to mask a detent problem until both the pin and the cam profile are worn.

Q: 13: Can you build a custom ratio?

A: Yes. Custom ratios, rack pitches and mounting geometries are normal scope for OEM integration. Because the ratio is fixed by the pinion pitch-circle diameter and the output sprocket diameter, a non-standard speed requirement is usually met by changing one or both of those dimensions, which leaves the housing envelope unchanged and keeps the unit inside the clearance already allowed for in your layout.

Q: 14: What tooth accuracy and backlash should we expect?

A: Pinion teeth are hobbed to AGMA Class 8 (DIN Class 8) and the flanks are finish-ground to within 0.015 mm of the theoretical involute after hardening. Backlash on a matched pinion-and-rack set is held between 0.10 mm and 0.20 mm. Rack tooth pitch is controlled to within 0.025 mm accumulated over any 300 mm of length.

Q: 15: How long does it take to install the unit on an existing trolley?

A: Bolting the housing to the trolley mounting plate and aligning the pinion to the rack is roughly a 30-minute job for an experienced maintenance team, once the rack is in position and the trolley is off the line. What takes longer is establishing the rack position and proving the alignment over its full length, which is why the zone layout is better agreed before the racks are ordered than during the shutdown.

Bearing gear spreader units and matched racks packed for shipment

 

Hot Tags: bearing gear spreader, China bearing gear spreader manufacturers, suppliers, factory, Cross Disc Spreader, spreader, Bearing Gear Spreader, Plating Conveyor Spreader, C Shaped Spreader, Cross Spreader

Send Inquiry

whatsapp

Phone

E-mail

Inquiry