Five Tons Series Lifting Group Rail
video

Five Tons Series Lifting Group Rail

Used at the ascending and descending points where the conveying chain travels. It can be cut to any angle according to the installation site conditions, but the angle should not be greater than 45°. However, the influence of the distance between two adjacent spreaders in ascending and descending should be considered.
Send Inquiry
Product Introduction

Hangzhou Ocean Industry Co., Ltd. is one of the most experienced manufacturers and suppliers of five tons series lifting group rail in China. Welcome to wholesale customized five tons series lifting group rail at competitive price from our factory. Good service and quality products are available.

 

Product Description

Hangzhou Ocean Industry Co., Ltd. manufactures lifting group rails at its own plant in Hangzhou, China, for the incline and decline points of overhead conveyor circuits. A lifting group rail is the inclined track section that raises a conveyor chain from the entry level of a line to the working height of a process station, and lowers it again on the return. It is built as a matched assembly - inclined rail, lifting carriage, drive, travel limits and anti-fall protection - so that the elevation change happens inside the conveyor rather than at a separate hoist or transfer with its own operator, its own interlocks and its own set of failure modes.

The rail is designed around a working inclination limit of 45°. Inside that limit the angle is set to suit the building rather than the other way round: a shallow incline where floor length is available, a steeper one where the line has to climb quickly between two existing structures. The limit protects the behaviour of the chain and the load on the slope, not the strength of the rail section itself, which is why the standard range stops at 45° and one long-stroke model is held to 40°.

Standard configurations cover lifts from 1,500 mm to 4,000 mm at a rated capacity of 5,000 kg, with lift speeds from 3 m/min to 6 m/min and matched 5-ton series straight track at both ends. We also help line builders set the clearance between adjacent spreaders through the lifting zone, because the point where an incline meets a straight section is where carriers bunch up, and a spacing that is slightly too tight there turns an elevation change into a collision or a bottleneck instead of a smooth transfer.

The application is any conveyor line that has to change elevation as part of its process: cathodic electrodeposition and powder coating lines climbing into a curing oven, pretreatment tunnels where the entry track runs at floor level and the process track runs above head height, and assembly or machining lines where parts have to be presented at a fixed working height at one station and carried away at another. In all of those cases the lifting group rail is the component that makes the elevation change part of the conveyor rather than a separate handling step.

Lifting group rail section for overhead conveyor incline and decline

Request a Lifting Group Rail Quotation - send your lift distance, load capacity and cycle time to oceanindustry@vip.163.com.

What a Lifting Group Rail Does on a Conveyor Circuit

On a circuit with an elevation change, the inclined section is where the conveyor stops behaving like a horizontal machine. Everything that travels on the straight track - the chain pull, the trolley loading, the carrier spacing - is resolved differently once the track is at an angle, because gravity now has a component along the direction of travel rather than only across it. The lifting group rail is the packaged answer to that section: it carries the vertical load, holds the chain on the raised profile, changes the elevation at a controlled speed, and stops if anything about the travel goes outside the limits it was set up for.

The alternative is to break the line at floor level and re-raise the product with a hoist, a scissor lift or a transfer station. That works, but it adds a handling step, a control interface and a second set of interlocks, and every one of those is a point where the product can be dropped, marked or delayed. Building the elevation change into the track keeps the product on the same carrier from load to unload and keeps the change under the control of the one drive that is already running the line.

What the unit is expected to deliver in service comes down to three things. It has to carry the rated load over the incline without the trolleys losing contact with the track or the load hanging away from the carrier. It has to make the change smoothly, because a lift that snatches or judders transfers that motion into the workpiece - a problem that shows up as damage on a painted or plated surface long before it shows up as wear in the mechanism. And it has to place the carrier accurately at the top of the stroke, because the next station is usually an indexing position where the part has to arrive at a defined height before anything else can happen.

The structural side matters just as much on lines that run continuously. A lifting group rail on a pretreatment or coating line sits in an atmosphere of vapour, wash-down water and temperature change for years at a time, and the frame, joints and guides have to hold their geometry through that. A section that stays rigid and stays square is a section that comes out of the annual maintenance list, which is where most of the real cost of a lifting installation accumulates.

Lifting Group Rail Configurations

The four standard models differ by stroke, and the rated speed and cycle time come down as the stroke gets longer - a longer travel at a fixed drive power takes longer to complete, and the inclination limit tightens on the longest model. All four are built on the 5-ton series straight track profile, so they do not introduce a second rail section type into a line.

Model

Lifting stroke

Lift speed

Cycle time per lift

Inclination range

Matched track section

LT-5000/1500

1,500 mm

4 to 6 m/min

30 seconds or less

0° to 45°

5-ton series straight track

LT-5000/2500

2,500 mm

4 to 6 m/min

45 seconds or less

0° to 45°

5-ton series straight track

LT-5000/3000

3,000 mm

4 to 5 m/min

60 seconds or less

0° to 45°

5-ton series straight track

LT-5000/4000

4,000 mm (custom)

3 to 4 m/min

90 seconds or less

0° to 40°

5-ton series straight track

The rated capacity is 5,000 kg across the range. Where a project needs a stroke between two of the standard figures, the stroke is built to the figure the layout calls for and quoted as a variant of the nearest model rather than as a new design.

Incline and Decline Geometry: The 45° Working Limit

The angle of the inclined section is the first decision on any lifting installation and it is usually made by the building, not by the process. The height difference between the entry track and the process station is fixed by whatever the station has to be at, and the horizontal run available for the climb is fixed by the floor plan. The angle comes out of those two figures, and what the 45° limit does is tell you whether the layout will work as drawn before anything is ordered.

Two things change as the angle steepens. The first is the load path: the component of the load acting along the incline rises with the angle, so the chain has to carry more of it and the rail has to resist more of the resulting reaction. The second is the behaviour of the carrier itself, because a trolley that sits comfortably on a rail at a shallow angle starts to hang away from the track, and a load that is only restrained by gravity on the level has to stay attached and in position on a slope. The working limit of 45° is the point at which those two effects are still comfortably inside the capacity of the 5-ton series profile and its trolleys. The longest standard stroke is held to 40° for the same reason - a longer inclined section carries more than one carrier at a time, so the load case at the steepest angle is less forgiving.

Where the incline meets the straight track, the transition is a designed part of the section rather than a cut joint. Both the entry and the exit of the slope are places where the chain changes direction and where a kink in the track produces a shock load every time a carrier passes. Getting the transition geometry right is what allows the same drive to run the level sections and the incline without a step change in chain tension at the joints.

Track Continuity and Profile Matching

The inclined section has to be the same profile and the same material grade as the straight track it joins. That requirement sounds administrative and is not: a transition between two different structural grades has two different coefficients of thermal expansion and two different stiffnesses, and the joint between them is where that mismatch shows. On a line that runs through a curing oven, an e-coat tank enclosure or an outdoor section, the movement at that joint accumulates over the length of the incline until the fixings at the joint carry loads they were not sized for, and the failure appears as a loosened or cracked joint rather than as anything obviously thermal.

Mixing structural grades within one line is the specific risk here. A Q235B section carrying on from a Q345B section is the combination that comes up most often, because both are readily available and the difference is not visible on the outside of the rail. The same applies to rail profile: the inclined section has to present the identical running surface and the identical trolley slot as the adjacent straight track, otherwise the trolleys step, the chain wears unevenly at the joint, and the section has to be re-cut.

For a quotation, the practical way to close this out is to send the specification of the track the incline will join - profile drawing, material grade, and the joint detail already used on the line. Where a project is being built from scratch, the whole circuit is specified from one drawing set and this problem disappears by design. Where a lifting group rail is being added to a line that already exists, the adjacent track governs, and the incline is built to match it.

Chain Compatibility and Trolley Spacing on Slopes

The chain on an incline is the same chain that runs the level sections, and it has to be, because the pitch is fixed by the sprockets at the drive and by every trolley on the circuit. For the 5-ton series the standard pitches are 200 mm and 250 mm, and the pitch on the lifting group rail has to match the pitch already on the line. A mismatch here is not a compromise that can be absorbed by adjustment: the section simply will not run.

Pitch matters more on the slope than the number alone suggests, because the chain on an incline is carrying an extra axial load and the way that load is spread between the trolleys depends on how many of them are on the slope at once. On a short, steep incline the chain is working with fewer carriers on the incline at any moment; on a long, shallow one it is working with more, and each of them adds rolling resistance and a share of the vertical load. That is the point at which trolley spacing becomes a design figure rather than a layout convenience.

Spacing also decides whether spreaders clear each other through the lifting zone. The spacing that works on the level can be too tight once a group of carriers is tilted through an incline and a transition, because the effective length of each carrier along the direction of travel changes with the angle. Working that clearance out on the drawing - rather than discovering it during commissioning when two spreaders come together at the top of the stroke - is part of the technical support we provide with the rail. It is also the single most common cause of a line that runs perfectly on the level and jams the first time it climbs.

Safety Devices and Travel Limits

A lifting group rail is one of the few places on an overhead conveyor where the load can fall, so the protective devices are part of the assembly rather than accessories ordered afterwards. Each unit is supplied with overload protection and an anti-fall device, and with a limit switch carriage that reports the position of the travel to the line control system.

The two protection functions answer different faults and it is worth being clear about which is which when a line is being specified. Overload protection guards the drive and the structure by stopping the motion when the force required to move the load exceeds what the section was sized for - typically because a carrier has jammed, a spreader has come up against something, or the payload is heavier than the one the line was designed around. An anti-fall device guards the position of the load by holding the carriage and its load if the lifting effort stops, which is what stands between a power failure or a broken chain and a load on the floor.

The limit switch carriage sets the top and bottom of travel. Where those limits are set is a decision with mechanical consequences: set the upper limit at the exact working height and the carriage arrives with the drive still pushing, which loads the structure at the end of every stroke; set it a few millimetres short and the carriage settles into the limit with no standing force. That is the arrangement we aim for, and it is why the switch position is checked during commissioning rather than left as delivered.

The structural design of the section contributes to safety in a less visible way. A rigid frame and guides that hold their geometry keep the trolleys tracking correctly through the slope, and a section that tracks correctly does not generate the lateral loads that wear guides, loosen fixings and eventually put a carrier off the rail. On a line running in vapour, wash-down water and temperature change, holding that geometry is also what keeps the section out of the maintenance schedule.

Drive Power and Duty on a Lifting Section

Sizing the drive on an incline is a matter of adding up three resistances rather than reading a figure off the model number: the load being lifted, the friction of the chain running over the slope and its sprockets, and the rolling resistance of every trolley that happens to be on the incline. The first of those is the one that changes with the design, so the load per lift and the number of carriers on the slope at once are the two figures that decide the motor.

Working condition

Drive motor

Full rated load at the lower end of the lift speed range

2.2 kW

Longest stroke, full load, continuous duty at more than 15 lifts per hour

3.0 kW or 4.0 kW

The reason for stepping up on continuous duty is thermal rather than mechanical. A motor that is adequate for an occasional lift has time to cool between cycles; a motor that is lifting back-to-back for a full shift does not, and the consequence of undersizing on that duty is not a motor that stalls but one that trips on thermal overload at an unpredictable point in the shift. That is a harder fault to trace than an obvious overload, because the line runs normally for most of the day and then stops for no visible reason.

Two figures from the line are needed to settle this at quotation stage: how many lifts the station completes in an hour, and whether those lifts are evenly spaced or arrive in batches. A station that lifts fifteen loads an hour in a steady rhythm is a different thermal case from one that lifts the same number in three bursts, and the second is the one that usually needs the larger motor.

Control and Signal Integration

The limit switch outputs and the overload signal from the rail have to be wired back to the same controller that runs the rest of the conveyor. On a modern line that controller is a PLC, and the first question to settle is the signal convention it expects: PNP (sourcing) or NPN (sinking). The two are not interchangeable at the wiring stage, and a mismatch between the sensors on the lifting section and the input card on the PLC is the single most common commissioning problem on these units.

Lines that predate PLC control - relay logic panels, older contactor-based installations, or a lifting station that is being added to a line whose control cabinet is not being replaced - take the dry-contact relay output version instead. That arrangement lets the rail report its position and its fault state through volt-free contacts that the existing panel can read without any change to the input wiring.

For installations that are being planned with line-level data collection in mind, Profinet and Modbus fieldbus integration is available through an optional gateway module, which puts the position, status and fault signals on the network instead of on individual input points. Where a line is being integrated into a plant-wide system, that module is usually specified with the rail rather than added later, because retrofitting fieldbus onto an existing lifting section means a control shutdown that a new build does not.

Whatever the control arrangement, three signals decide how the rail behaves in service: the upper travel limit, the lower travel limit, and the fault output from the overload and anti-fall circuits. Confirm before ordering which of those the line's controller will act on directly and which are being taken back to an operator station, because it changes how the rail is tested at commissioning and which failures bring the line to a controlled stop.

Foundations and Reaction Loads

A lifting group rail introduces forces into the building that a horizontal conveyor does not, and both ends of the section need reinforced concrete foundations rather than a bolted connection to the surrounding slab. The loads the foundations have to absorb are the static load of the section and its rated load, multiplied to cover dynamic shock - the design basis is 1.5 times the static load plus the dynamic component.

The dynamic component is what most often gets underestimated. It is not only the weight of the moving load; it is what happens at the two ends of the travel, where the carriage is decelerating into a limit or accelerating out of one, and where a jam on the line transmits a stalled drive torque into the structure instead of into motion. Those events are brief and irregular, which is exactly why they are easy to leave out of a foundation calculation that was done from the steady-state figures.

The two ends of the rail are the two load paths, and they are not symmetrical - the top of the incline carries the elevated track and the process station above it, and the bottom carries the entry track and the chain take-up arrangement. Both need to be defined before the civil work starts, because the cost of altering a foundation after the slab is poured is out of all proportion to the cost of sizing it correctly at the drawing stage.

How to Size a Lifting Group Rail in Four Steps

Step 1 - Establish the vertical lift distance. The lift distance is the height difference between the entry track, which is horizontal, and the elevated track at the process station. On most painting lines and pretreatment tunnels this falls between 1,500 mm and 2,500 mm. On automotive body assembly lines that include a skid transfer it is often 2,500 mm to 3,000 mm. Whatever the figure comes to, allow 200 mm of safety clearance above the highest expected lift point so that the carriage and the load have room to reach the limit without touching anything.

Step 2 - Calculate the lift speed from the line cycle. Lift speed is not chosen from a preference list; it follows from the cycle time the station has to meet. Required speed in m/min equals lift distance in mm divided by cycle time in seconds, multiplied by 0.06. A 2,000 mm lift against a 30-second cycle therefore needs 2,000 / 30 x 0.06, or 4 m/min, and the model selected should be rated at that figure or slightly above it. Beyond 6 m/min the extra speed starts to cost more than it returns, because the faster travel introduces vibration and works the chain harder - on a lifting section it is better to match the cycle than to overrun it.

Step 3 - Check the drive power against the duty. The motor has to overcome gravity, chain friction and trolley rolling resistance together, and the duty cycle decides how much margin it needs rather than the load alone. Where the station lifts in a steady rhythm at the lower speeds, the standard motor is enough; where the stroke is long and the station lifts continuously, the next size up is specified to keep the motor out of thermal overload - the guidance table above sets out where that line falls.

Step 4 - Confirm the electrical interface. Most modern lines are PLC controlled, so the signal convention has to be agreed up front: PNP for sourcing inputs or NPN for sinking inputs. For relay-based panels, specify the dry-contact output version. Where the installation is part of an Industry 4.0 project or a plant-wide data collection system, the fieldbus gateway module is specified with the rail rather than retrofitted afterwards - see the control section above for what each arrangement does with the limit and fault signals.

Project Reference: Automotive E-Coat Line Lift Sections

A new automotive e-coat line in Central China needed twelve lifting group rails to move body-in-white assemblies between the pretreatment zones, the cathodic electrodeposition tanks and the curing oven. Each unit was specified at a 2,500 mm stroke, a 6 m/min lift speed and a 5,000 kg load capacity, with Profinet integration to the line's Siemens S7-1500 controller. The units were supplied complete with limit switch carriages and anti-fall devices, and the installation was supported through commissioning. Fourteen months of three-shift operation followed without unplanned downtime on the lifting sections, and the same customer has since ordered eight further units to extend the line.

The configuration is a useful reference for anyone planning a similar line because it sits at the top of the standard range on two counts at once - full rated capacity at the highest lift speed - and because it is an e-coat environment, where the rail is exposed to tank vapour as well as to the temperature of the oven it feeds. Where a project is close to that combination, the same specification is a reasonable starting point; where it is well inside it, a shorter stroke and a slower lift will bring the drive power and the foundation loads down with it.

Installation and Vertical Alignment

Installation starts with the foundations, because the rail is set to them and not to whatever the surrounding floor happens to be. The two ends are levelled and set to the vertical alignment the drawing calls for, and the inclined section is then positioned so that the entry and exit transitions meet the straight track without a step at either joint. A rail that is level front to back but twisted along its length will still accept the carriage; it is the twist that shows up later as uneven guide wear and as a carrier that tracks to one side of the slot on the way up.

The joint at each end deserves the most attention of anything in the installation, because it is the point where the alignment of the whole circuit passes through a bolted connection. The running surface and the trolley slot have to continue without a lip, the chain has to pass the joint without a change in pitch, and the fixings have to be tightened in a sequence that does not pull the joint out of line as the bolts come up to torque. Leaving the joints to be checked after the first loaded run, rather than only before it, is worthwhile on any line: a joint that settles slightly under the first loads is normal, and it is much easier to correct during commissioning than after the line has gone into production.

Where the lifting section connects to a line that is already running, the sequence has to be planned around production rather than around the mechanics. The adjacent track governs the alignment, so the useful preparation is a survey of the existing track before the new section arrives: profile, grade, joint detail, and the level of the entry and exit points as they actually are rather than as the original drawings show them. A deviation found at that stage changes a drawing; the same deviation found at the joint changes a programme.

Commissioning Checks Before Handover

The checks that decide whether a lifting section will settle into production or keep coming back are a short list, and they are worth running in order rather than in whatever order the site allows. First the geometry: entry and exit joints aligned with no lip on the running surface or the trolley slot, and the incline set to the angle on the drawing. Second the limits: the upper and lower switch positions confirmed so the carriage arrives at the working height without standing force against the structure, and the fault outputs proven by tripping each protection in turn.

Third the electrical interface, which means reading the actual signals at the controller rather than at the sensor: PNP or NPN confirmed against the input card, and each limit and fault signal confirmed as landing on the input the drawing says it does. A signal that is wired to the right terminal but interpreted in the wrong sense is a fault that only appears when a protection operates, which is the worst moment to discover it. Fourth, the loaded run: the section cycled at rated load over the full stroke, with the chain tracked through both transitions and the carriage checked for any tendency to run to one side of the slot.

The last item is the one most often skipped and the most useful: run the section at load for long enough to warm the drive, then repeat the limit and speed checks. A motor that is marginal on duty will look correct on a cold first cycle and show its thermal behaviour only once the station has been lifting for an hour or more.

Inspection Points on Inclined Track

A lifting section rewards inspection more than most parts of a conveyor, because nearly everything that goes wrong on it announces itself visibly before it becomes a stoppage. The five checks below are all reachable from a platform, and none of them needs anything dismantled.

Look at the two joints first, where the incline meets the straight track at each end. The running surface should present a continuous line with no step and no bright polished mark at one edge of the slot; polish on one side is how a joint that has moved shows itself. Second, the transition sections, checking the chain for even wear and for any link that has begun to sit differently from its neighbours - a chain that is being worked harder on the slope wears at the transitions first. Third, the guides and the trolley slot along the incline, looking for one-sided wear or for the metal brightening on one face only, both of which mean the carriers are tracking to one side rather than running centred.

Fourth, the carriage and its travel: the carriage should move without play and without dragging, and it should reach both limits without any visible deflection in the structure at the top of the stroke. Fifth, the protective devices, checked as functions rather than as fittings - the anti-fall device tripped and proven to hold, and the overload protection confirmed as still able to stop the drive. Beyond the mechanism, two housekeeping items belong on the routine: fixings at both ends re-checked after the first weeks of loaded running while the structure settles, and the inclined track kept clear of process overspray, because coating that builds up on the running surface changes the effective geometry of the slope by a small amount that grows.

Site Conditions That Limit Lift Height

The stroke printed on a model sheet is a capability, not a decision - what a given site can actually install depends on conditions outside the rail. The first is headroom. The lift has to reach the working height with the safety clearance above the highest point of travel, and in an existing building the limiting factor is often the underside of a roof truss, a duct run or a sprinkler line rather than the height of the process station.

The second is the horizontal run available for the climb. A lift distance that is comfortable inside the 45° limit when there is ten metres of floor to climb across becomes unworkable if the available run is three metres, and the answer at that point is usually to rearrange the line rather than to ask the rail to do something the angle limit exists to prevent. The third is the foundation condition: both ends need reinforced concrete able to take the reaction loads, and a building with a suspended slab, a mezzanine floor or a shallow ground-bearing slab may need local foundations before a lifting section can be installed at any height.

The fourth is the environment the elevated track ends up in. If the top of the lift puts the process station inside a curing oven, above a heated tank or in a wash-down zone, the section sits in temperature and vapour for its whole life, and the adjacent elevated track has to be compatible with it as well - which brings the specification back to the profile and grade matching described earlier. Checking those four conditions before choosing a model is what keeps a lifting project to one drawing cycle.

Applications on Paint, Pretreatment and Assembly Lines

Cathodic electrodeposition lines are the heaviest users of lifting group rails, for a structural reason: the pretreatment stages are arranged as a sequence of tanks at low level and the e-coat tank and curing oven are arranged as a single elevated pass. Parts have to be carried into the tanks, raised out of the immersion, transferred along the elevated track and lowered again at the end of the sequence. Each of those elevation changes is a lifting section, which is why a full e-coat line may carry a dozen or more of them, each one matched to the same track profile and the same chain pitch as the rest of the circuit.

Powder coating and liquid paint lines use the same arrangement for the climb into the curing oven. The entry track runs at a comfortable loading height, the oven pass runs at whatever height the oven imposes, and the lifting section bridges the difference at a speed set by the line cycle. Because the lifting section is driven and controlled inside the conveyor, the oven pass can be laid out entirely around the process - dwell time, oven length, booth position - without any of those decisions being constrained by where the operator needs to hang a part.

Pretreatment tunnels rely on the same principle in the other direction, lowering the line from the process height back to a working height for unloading. On appliance, furniture and machinery assembly lines the requirement is usually positioning rather than height: a station that has to present a part at a fixed working height above the operator while the rest of the circuit runs at a different level. In every one of these cases the section does the same job - it makes the elevation change part of the conveyor, so the product stays on one carrier and the change stays under the control of one drive.

FAQ

Q: 1: What is a lifting group rail, and where does it sit in a conveyor circuit?

A: It is the driven inclined track section that changes the elevation of the conveyor chain - typically raising the load from the entry track of a line up to an elevated process pass, or lowering it back for unloading. It carries its own carriage, drive, travel limits and anti-fall protection, so the elevation change takes place inside the conveyor instead of at a separate hoist or transfer station.

Q: 2: What is the maximum inclination, and why is it limited?

A: The working limit is 45°. The longest standard stroke, the 4,000 mm model, is held to 40°. Two things set that ceiling: the share of the load that acts along the incline and has to be carried by the chain, and the way a trolley behaves on a steep slope once gravity is no longer holding the load squarely against the track. Inside the limit the angle can be set freely to suit the building.

Q: 3: Which model should I choose for my lift distance?

A: Match the stroke to the height difference between the entry track and the elevated process track, and remember to allow 200 mm of clearance above the highest point of travel. Send us that distance plus the load per carrier and the cycle time the station has to meet, and we will confirm which standard model covers it or whether a stroke between two standard figures is the better answer.

Q: 4: How do I work out the lift speed I need?

A: Divide the lift distance in millimetres by the cycle time in seconds and multiply by 0.06 to get the required speed in m/min. A 2,000 mm lift against a 30-second cycle works out at 4 m/min. Select a model rated at that figure or just above it rather than well above it.

Q: 5: What happens if I specify a lift speed above 6 m/min?

A: You gain cycle time and pay for it elsewhere. Above roughly 6 m/min the travel starts to introduce vibration and to work the chain harder, which shortens chain life and puts extra load into the joints and the guides at both ends of the incline. Where the cycle allows it, matching the station's actual rhythm is the better trade than overspecifying the speed.

Q: 6: Which chain pitch does the 5-ton series use?

A: The standard pitches for the 5-ton series are 200 mm and 250 mm. The lifting section is built to whichever pitch is already running on your circuit, because the pitch is fixed by the drive sprockets and by every trolley on the line - it is not something that can be adjusted on site. Confirm the figure at enquiry stage.

Q: 7: Can the incline be joined to track from another supplier?

A: Yes, as long as the joining track matches in profile and material grade. The combination that causes trouble is carrying a Q235B section on from a Q345B one, because the two have different stiffness and different thermal expansion and the joint between them ends up absorbing that difference. Send the profile drawing and grade of the existing track and we will build the incline to match it.

Q: 8: Which safety devices are supplied as standard?

A: Overload protection, an anti-fall device, and a limit switch carriage that reports the position of the travel to the line controller. The overload protection stops the drive when the force needed to move the load exceeds the design figure, and the anti-fall device holds the carriage if the lifting effort is lost. Both are proven as working functions during commissioning, not only checked as fitted.

Q: 9: Does the PLC need PNP or NPN inputs?

A: That has to come from your control drawings, and it is worth checking rather than assuming - PNP (sourcing) and NPN (sinking) sensors are not interchangeable at the wiring stage, and a mismatch here is the most common commissioning problem on these units. For relay-based panels that predate PLC control, specify the dry-contact relay output version instead, which reports position and fault state through volt-free contacts.

Q: 10: What foundation does the unit need?

A: Reinforced concrete foundations at both ends of the inclined section, sized to absorb 1.5 times the static load plus the dynamic component. The dynamic part covers deceleration into the limits and the stalled-drive condition if the line jams, both of which are brief but are what the foundations actually have to survive. Foundation design is a civil work item and should be settled before the slab is poured.

Q: 11: How do I avoid collision between adjacent spreaders through the lifting zone?

A: By working the clearance out on the drawing rather than on site. The spacing that works on level track changes once a group of carriers is tilted through an incline and its transitions, because each spreader occupies a different length along the direction of travel than it does on the level. Send the carrier spacing, the spreader dimensions and the lift distance and we will confirm the spacing that clears through the whole stroke.

Q: 12: Can the drive be sized for continuous duty rather than intermittent lifting?

A: Yes, and on a long stroke it should be. The step up is about heat rather than force: a motor lifting back-to-back for a full shift has no time to cool between cycles and will eventually trip on thermal overload rather than stall. Tell us how many lifts the station makes in an hour and whether they arrive in a steady rhythm or in batches - the batch pattern is the one that needs the larger motor.

Q: 13: Can you supply the inclined section as a complete package?

A: That is the normal way it is supplied: inclined rail, lifting carriage, drive, limit switch carriage and anti-fall protection as one assembly, matched to the 5-ton series straight track at both ends. Anything that has to interface with the rest of the circuit - track profile, chain pitch, signal convention, foundation loads - is agreed before the order rather than after it.

Q: 14: What is your delivery lead time?

A: A sample section is produced in 30 working days, and a production quantity in 60 working days counted from receipt of the deposit. Where the section has to match track that is already installed, the lead time runs from the point the existing profile and grade are confirmed, since the incline is built to those figures.

Q: 15: What are your payment terms?

A: Payment is by T/T, with 30 percent accompanying the order and the balance before shipment. Photographs of the completed section, its carriage and the packing are sent before the balance becomes due, so what is being shipped can be checked against what was agreed.

Lifting group rails and inclined conveyor track packed for shipment

 

Hot Tags: five tons series lifting group rail, China five tons series lifting group rail manufacturers, suppliers, factory, lifting rail system, Heavy Duty Lifting Group Rail, Industrial Series Lifting Group Rail, Five Tons Series Lifting Group Rail

Send Inquiry

whatsapp

Phone

E-mail

Inquiry